SUPPORT

INSTRUCTIONS  FOR  USE

WARNING∶
Improper use of dive instruments may result in serious injury or death.Read
and understand these instructions thoroughly before you dive .
PRESSURE GAUGE / SYNTHETIC CASE
*The pressure gauge with H.P is made to be used with compressed air only.
*Link the hose at the jacket to avoid pressure gauge traverse.
*maximum pressure = 5,000psi(350bar)
Temperature= 0 to 100℉(-5° to 45℃)
Thread size=7/16” ╳ 20- UNF
*Connect the hose to the high connection of the regulator ,after preventively having anointed the O-rings with silicon grease.
*The pressure gauge with H.P.hose satisfies the requisite of the European Normative specifications CE EN250.
Preciseness:
Standard of precision by CE EN 250 NORM
± 5bar a 50bar   ( ± 70psi a 700psi)
±10bar a 100bar  ( ±140psi a 1,400psi)
±10bar a 200bar  ( ±140psi a 2,800psi)
±10bar a 300bar  ( ±140psi a 4,200psi)
Upkeep:
*The wear and tear subjects  components of the pressure gauge like H.P. hose , pivot pin , O-Rings , must be periodically verified and replaced.
*With the purpose to limit the deterioration of the O-Rings we recommend the periodical use of compatible lubricant.
*After the use , rinse the complete pressure gauge with fresh water and keep the instrument dry.
ATTENTION
*Always keep the pressure gauge dial away from your face when turning on your tank valve.
*Dont use solutions to clean the glass (the raw material could lose his unbreakable characteristic).
*Never obstruct the one-way vent valve located on the back side of the gauge.
*Use two 15mm wrench to close , not forcing the link excessively.
DEPTH  GAUGE
*The black needle with red tip indicates current depth and as depth increases it pushes the thinner needle.
*To reset the max depth thinner needle for a new dive,turn the slotted knob located in the center of the gauge face counterclockwise until it just makes contact with the black needle with the red tip.
*steel(copper-berylium for military) membrane system of reading that elevated sensibility and precision.
*Dial with parabolic scale to improve the precision of reading on the various depths.
*Dont  expose the tool to sources of heat.
*The employment over the maximum value of suitable scale on the dial can damages the tool in irremediable way.
*The Depth gauge satisfies the requiste of the European Normative
specifications CE EN 250,13319.
Preciseness:
Standard of precision by CE EN 250 ,13319 NORM.
(+0.8m.-0.4m) a 3 meter    ( +2.62 ft.-1.31 ft ) a  10 ft
(+0.8m.-0.4m) a 6 meter    ( +2.62 ft.-1.31 ft ) a  20 ft
(+0.8m.-0.8m) a 9 meter    ( +2.62 ft.-2.62 ft ) a  30 ft
(+1.0m.-1.2m) a 15meter   ( +3.28 ft.-3.93 ft ) a  50 ft
(+1.0m.-1.2m) a 30meter   ( +3.28 ft.-3.93 ft ) a 100 ft
(+1.0m.-1.5m) a 45meter   ( +3.28 ft.-4.92 ft ) a 150 ft
(+1.0m.-1.5m) a 60meter   ( +3.28 ft.-4.92 ft ) a 200 ft
(+1.0m.-1.5m) a 70meter   ( +3.28 ft.-4.92 ft ) a 230 ft

ATTENTION
*Rinse the depth gauge with fresh water after dive and not employ solutions to clean the glass(the material could lose the characteristics of impermeability or transparency if put in contact with not compatible substances).
*Do not obstruct the depth sensor opening located on the back side of the gauge.
*Never over come the maximum attainable depth from the tool(equivalent to the end scale printed on the dial of the tool)

UNDERWATER COMPASS
*The compass is mainly used to follow a predetermined direction.
The red line on the covert glass,points out the direction that you need to take.
*Always avoid the direct expose of the tool to the sun or to sources of heat and rinse afterdive with fresh water.
*The contained liquid in the compass can develop bubbles of air if exposed to sources of excessive heat.These bubbles dont invalidated the good working of the compass and they have the tendency to disappear when temperature come back to normal condition.

WARRANTY
Conditions of warranty:
* instruments have a warranty of two years from manufacturing
date.(H.P hose have a warranty of one year)
*The warranty covers pieces recognized faulty by our technicians for
manufacturing or material defect.

The warranty doesnt cover:
*damage caused by shocks , fallings or bad use in surface or
dive,aspect or functioning defects caused by usual products  aging.
*The warranty declines in case of products manipulation or opening
by person lacking of adequate technical if necessary,or product
tested with not adequate control equipment.
*The periodical maintenance and the replacement of fatigue subject components during the use.
*The maintenance and replacement of swivel and respective O-ring.
*The replacement of flexible tube high pressure hose.
*Warranty does not extend to plastic gauge faces , rubber
boots , O-rings , hosefitting corrosion .

Repair estimate :
*Not yet under warranty instruments will be subject to repair estimate with payment in
advance.
*The repair will begin only after customers confirmation to proceed and respective
payment.
*Delivery costs for instrument return,Is charged to the customer.

Limitation of Liability
To the maximum extent permitted by applicable mandatory laws, this limited warranty is
your sole and exclusive remedy and is in lieu of all other warranties, expressed or implied.
Scubabest shall not be
liable for special, incidental, punitive or consequential damages. Scubabest shall not be
liable for delay in rendering warranty service.